Why Learning Plumbing Basics is Crucial for Installing a Bathtub
Why Learning Plumbing Basics is Crucial for Installing a Bathtub
Blog Article
What are your insights and beliefs about How to Install a Bathtub?
Installing a bath tub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, and also occasionally, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably difficult task. If the old tub is conveniently easily accessible, the task can move speedily; if you need to open a wall to eliminate the old bathtub as well as position the brand-new tub, the task is much harder. In either instance, the task is within a home handyman's skills, although you will certainly need a helper to vacate the old bathtub as well as embeded in the brand-new one. Ensure you have qualified on your own for the job and also are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you might need an expert plumber to make tube links.
This write-up will help you mount a brand-new bath tub in your restroom if you have actually currently gotten a brand-new bathtub as well as do not need to alter the arrangement of your previous water supply pipelines.
Your devices and material checklist need to make up the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you must do is disconnect the supply of water. After doing so, switch on the taps to drain any kind of water staying in the system. The procedure of getting rid of the existing faucets can be rather problematic because of the limited accessibility that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the staying water that will come from the pipelines. Once the supply pipes have been gotten rid of, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. When the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Before moving on to fit the new taps, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin ensuring that the washers are in area in between the faucet and the sink. Secure the faucet in place with the manufacturer supplied backnut. As soon as the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular tap ports. The previous kind should be attached to the tap finishes first, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Making use of the two wood boards under its feet, position the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four small factors.
The following goal is to make sure that the tub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the tub up until the level reviews degree.
To install faucets, fit all-time low of the outermost versatile tap connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Turn on the supply of water as well as examine all joints and new pipework for leaks and tighten them if necessary. Fill the bath tub as well as likewise examine the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, repair the bathroom paneling as explained in the maker's instruction manual. Tiling and sealing around the bathtub should wait up until the bath tub has actually been made use of at least once as this will resolve it right into its last position.
Preparing for the Installation
Firstly, the sustaining framework provided with the bathroom must be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps system to avoid strain on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to break a rigid seal, triggering the water to pass through the wall in between the bathroom and also the tiling, causing difficulties with wetness and feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to enable the motion experienced when the tub remains in usage. The sealant can break fairly early if you do not take into consideration this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily readily available on the market. It is advisable to fit the ceramic tiles using waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
As a fervent person who reads about A Step-by-Step Guide to Installing a Bathtub, I think sharing that topic was really helpful. Those who enjoyed reading our article plz do not forget to pass it around. We cherish reading our article about How to Install a Bathtub Yourself.
Pipe burst? Phone now! Report this page